Yt27 Air-Leg Rock Drill/Hand-Held Pneumatic Rock Drill

• Customization: Available
• Transport Package: Wood Case and Carton
• Trademark: GM
• Model NO.: YT27
• Origin: China
• Production Capacity: 1000set/Year

Product Description

The YT27 rock drill is a kind of high efficiency air leg rock drill machine. It is mainly used for blasting holes and other drilling works in a quarries, railway construction, water conservancy construction and national defence project facility.

When it is matched with Model FY250 Oil reservoir and Model FT160A or FT160B Air-leg , it is suitable for wet drilling under various of rocks at aclinic and incline orientation, it can also use in the trolley without Air-leg.

Specification
Weight                                                        27 kg
Outside dimension(L×W×H)                  668×248×202mm
Cylinder dia                                                  80mm
Piston stroke                                                60mm
Impact energy                                             ≥75.5J
Impact frequencey                                      ≥ 36.7Hz
Air consumption                                          ≤83.3L/S
Air pipe (inner dia)                                        25mm
Water pipe (inner dia)                                   13mm
Air pressure                                                 0.63MPa
Water pressure                                            0.3MPa
Bore dia                                                      34-45mm
Bore depth                                                       5m
Shank dimensions(hex×length)             22×108±mm×mm

Model FY250B oil lubircator
Weight                        1.2kg
Oil capacity                 0.25L
Air leg                        FT160A                       FT160B
Weight                         17kg                           16 kg
Llength: max              3006mm                    2526mm
min                            1668mm                     1428mm
Propulsion stroke      1338mm                     1098 mm
Axis thrust (max)         2000N                        2000N

Notice
1. Dismantling new machines and clean the parts, dispose of antirust grease before using it. The parts of exterior must be lubricate when relocate, then operate and check machine about 10minutes and is low air pressure (0.3Mpa) before using it.
2. The air pressure should be kept at 0.5-0.63 MPa.(measure in rubber tube), if the air pressure is too high, it will damage parts fast. And if the air pressure is too low, it will affect the speed of drilling and the machine is also normal working.
3. Before using machine, blow off dirty to protect parts. inspect the screw thread whether is tight and the operator handle whether is free to move, ensure machine operate normally .
4. The lubricating oil into oil reservoir before using machine and mix up the accelerograph. and do not operate machine without lubricating oil.
5. Before using machine, increase holding power, while operate machine increasingly. Do not operate machine at the max thrust or should not idle machine for a long time, it will damage parts.
6. Dismantling water pipe and operate machine after blasting holes. It can blow off the rest moisture and protect the parts away from rusting .
7. The rock drill is centre water-injection drilling. Do not operate without water and dismantle water needle. If dismantle the water needle ,the machine will not operate.
8. Tighten two side bolt nuts to protect parts and tighten air pipe to aviod hurt.
9. If machine should store for a long time. Diamantle machine first, oil and seal them, then put it in a dry place.

Lubricating oil
Lubrication has great influence in the performance and working life. Do not operate machine without lubricating oil, it is better that not use grease lubrication avoid to obstruct pipeline, reduce machine efficiency and acceleration element wear. In different season has different oil.

Temperature	Name	NO.	Kinematic viscosity	Solidifying point	Standard
-30--10	Refrigerator oil		11.5-14.5(50ºC)	-40ºC	ZBE34003-86
-10-0ºC	Turbine oil	N22	20-23(50ºC)	-10ºC	GB2537-81
0-30ºC	Cylider oil (30%) Machine oil (70%)	HG-24+HJ-50	20-28(100ºC) 47-53(50ºC)	15ºC -10ºC	GB447-77 GB443-84